CRYLI-TEK® 5500

Concrete Sealer

The difference is in the finish


We took all the best attributes of the 5505 - clear, non-yellowing, UV stable and made it into a satin finish water-based formulation. We call this decorative sealer the Cryli-Tek 5500.

CRYLI-TEK 5500

$64.88

1 Gallon: $64.88

 

 

Clear

Description

The difference is in the finish

We took all the best attributes of the 5505 – clear, non-yellowing, UV stable and made it into a satin finish water-based formulation. We call this decorative sealer the Cryli-Tek 5500.

Additional information

Weight N/A

What it is

Water-based, satin / low sheen decorative concrete & masonry sealer

What it's for

Concrete driveways, patios, pool decks, stamped concrete, pavers, aggregate, stone

What it does

Protects and beautifies decorative concrete, stone and masnory

What it's made of

Water-based styrene acrylic polymers

Discover the look of satin

A water-based concrete sealer never looked so good

What's the finish/color

Clear, low sheen / satin

How do you apply it?

1/4" - 3/8" high quality nap roller or brush

What's so special about it

Long lasting satin / low sheen, resists chipping, flaking, delamination and breakdown from UV light exposure

What else is like it?

Cryli-Tek 5505: is solvent-based and leaves a high gloss / wet look finish

Gallery

Photos and videos of Ghostshield concrete sealers in action

Technical

Technical specs, application instructions, testing data

CRYLI-TEK 5500 RISES ABOVE


Cryli-Tek 5500 meets or exceeds the following tests:

ASTM D-3359: Adhesion

ASTM D-3363: Film Hardness

ASTM D-4541: Pull-Off Strength

ASTM G-155: Accelerated Weathering

ASTM D-2047: Static Coefficient of Friction


TECHNICAL SPECS

  • Feature: Decorative sealer
  • Chemistry: Acrylic
  • Color: Clear
  • Finish: Satin, low sheen
  • Category: Coating
  • Carrier: Water
  • Packaging: 1 Gallon
  • Coverage: 250 sq. ft. per gallon
  • Interior/Exterior: Interior/Exterior
  • Application Method: Roller
  • Application Temperature: 45 F - 90 F
  • Number of Coats: 1
  • Drying Time (dry to touch): 3-5 Hours
  • Drying time (full cure): 24 Hours
  • Time before/after rain: 48 Hours
  • Storage/Shelf Life: 1 Year
  • Clean up: Soap/water
  • Paintable: No
  • VOC Content: 80 g/L

PREPARATION

  1. New “green” concrete must be properly cured. Concrete should obtain 80% of design strength, typically achieved within 14-28 days.
  2. The concrete substrate must be structurally sound and clean of oil, grease, dirt, wax, curing compounds, efflorescence, paints, previous sealers, adhesives and other contaminants that might interfere with the penetration of the sealer. Power wash, acid etch or mechanically scarify as necessary to achieve the desired surface condition. If acid was used to clean the concrete, neutralize the surface and rinse with water prior to application. Allow for proper dry time before application. The surface-zone moisture content of the concrete should not exceed 4% wt. Do not apply if standing water is visible.
  3. Surface and air temperatures must be at least 60°F during application. Surface and air temperatures should not exceed 90°F. Do not apply when temperatures are expected to fall below 32°F within 8 hours or when rain is expected within 12 hours following application. Keep material from freezing. If freezing conditions exist before application, let the substrate thaw before application. Do not apply during inclement weather or when inclement weather is expected within 12 hours.
  4. Crack, patching and expansion joint sealants can be applied before application; always test for compatibility and adhesion.
  5. Protect people, property, vehicles, window glass, roofing materials, plastic products, shrubbery, landscaping and all surfaces not set for treatment from overspray.

APPLICATION

  1. Always test a small area before application to ensure desired performance, aesthetics, coverage rates and to verify application technique. Let test area dry thoroughly, 5-7 days, before inspection.
  2. One continuous, thin, uniform coat is needed to ensure complete coverage. Apply a with a good quality roller or brush. Too thick of an application will result in entrapment and subsequent product failure. If it starts to rain, stop treatment and cover the treated areas.
  3. If an additional coat is desired wait at least 4 hours and ensure the first coat has completely dried before applying a second coat. Press on the coating with your thumb to verify that no fingerprint impression is left. If no impression is created, then the recoat can be started. Always remember that colder temperatures will require more cure time for the product before recoating can commence. We do not recommend any coatings be placed over this product except multiple coats of this product itself.

NOTES

Dry Time

Typical drying time is 4-6 hours at 70°F and 50% relative humidity. Cooler temperatures or higher relative humidity can extend the drying time. Treated surfaces will be ready for pedestrian and vehicle traffic within 24 hours.

Clean Up

Clean equipment and tools with soap and water. Unused or old material may be disposed of in a waste disposal site in accordance with local, state and federal laws.

Precautions/Safety

Avoid contact with skin, eyes and clothing, do not take internally. Use appropriate safety equipment during application and handling. Please refer to the safety data sheet (SDS) for additional precautionary instructions before use.

Best Performance

Proper application is the responsibility of the user.

  • Make sure the most current versions of technical data sheets and safety data sheets are being used.
  • Do not use in immersion service or constant chemical exposure areas.
  • Extremely porous substrates such as pavers may require additional coats to achieve a slight enhancement.

Coverage

1 coat: 100 - 300 square feet per gallon. Variations in texture and porosity of substrate will affect the coverage and performance of the product.

FAQ

Does the concrete need to be dry before sealing? Yes, the concrete needs to be as dry as possible before sealing. We recommend the moisture content of the concrete be less than 4% wt. It is recommended to wait at least 24-48 hours after rain and pressure washing before sealing.

What can I use to apply this product? The Cryli-Tek 5500 can be applied with a 3/8" nap paint roller or brush.

What is the difference between the Cryli-Tek 5500 and the Cryli-Tek 5505? The Cryli-Tek 5500 is a water based acrylic that will leave a matte/satin finish. The Cryli-Tek 5505 is a solvent based acrylic that will leave a high gloss, wet look finish.

 

Ghostshield in action

Recent project videos showing how to seal your concrete with Ghostshield

Caoba Miami WORLDCENTER

Our latest project in Florida was for the beautiful new Caoba Apartments, part of the new Miami Worldcenter. Ghostshield was the perfect sealer for their high-traffic parking garage.

432 Park Avenue New York

432 Park Avenue - the tallest residential building in the Western Hemisphere - sealed with our flagship commercial product, Iso-Tek 8501; a thixotropic sealer.

STAMPED CONCRETE CLEAN AND SEAL

View the Micro-Degreaser 1100 a non-acid-based, non-toxic cleaner and the Siloxa-Tek 8510 a deep-penetrating oil and salt repellent sealer in action.

TOP